info@nfpmotor.com
Need For Power Electronics Co., Limited · +852 5142 2310
KH SERIES / GEARBOX Illustrative render
Illustrative product rendering based on the GB15-154-DZ23008-1 assembly drawing
15 mm body / gearbox Source page 24 / 41

GB15-154-DZ23008-1

15 mm 154:1 Planetary Gearbox

Compact motion. Precisely geared.

15 mm planetary gearbox with a 154:1 transmission ratio. This catalogue sheet supplies mechanical drawings only.

Reduction ratio
154:1
Maximum front diameter
15.7 ±0.1 mm
Overall length
61.0 mm
Shaft diameter
6.0 +0/-0.03 mm

Part / series no. GB15-154-DZ23008-1

01 / TECHNICAL DATA

Specifications at a glance.

154:1

Electrical performance, construction and operating data for the specified configuration or motor family.

Mechanical reference · 01

Mechanical reference · 01
Transmission ratio 154:1
Front flange diameter 15.7 ±0.1 mm
Body diameter 14.6 ±0.1 mm
Overall length 61.0 mm
Body length behind flange 39.4 ±0.1 mm
Output projection 21.6 ±0.1 mm
Shaft diameter 6.0 +0/-0.03 mm
Shaft tip diameter 5.0 +0/-0.1 mm
Shaft tip flat dimension 4.0 +0/-0.1 mm
Shaft flat dimension, side view 4.0 +0/-0.08 mm
Shaft-tip segment 2.2 mm

Mechanical reference · 02

Mechanical reference · 02
Circumferential groove width 1.0 +0.05/0 mm
Output end segment length 14.9 ±0.1 mm
Pilot diameter 11.0 mm
Front flange thickness 1.0 mm
Front mounting feature length 6.7 mm
Inner mounting feature length 4.3 mm
Slot width 2 × 3.3 mm
Mounting holes 2 × Ø2.0 mm, counterbore 3.5 mm
Front shoulder dimension 0.9 mm
Mounting-hole center offset 3.0 mm
Rear feature length 3.0 mm
Technical notes
  • Unspecified linear tolerances (GB/T 1804): under 3 mm ±0.05 mm; 3–6 mm ±0.05 mm; 6–20 mm ±0.1 mm; above 20 mm ±0.15 mm.
  • No electrical performance data are supplied on this source page.
  • Mechanical dimensions and tolerances follow the two source views.

02 / MECHANICAL REFERENCE

Dimensions & assembly layout.

English drawing labels with original dimensions and tolerances. Open the image to inspect the full drawing.

Outline drawing Unit: mm
GB15-154-DZ23008-1 outline dimensions and assembly geometry
Outline drawing · Dimensions and tolerances retained from source drawing.

04 / DESIGN INTEGRATION

From drawing to your mechanism.

01 / FIT

Confirm the envelope.

Review the gearbox dimensions, mounting interface, shaft geometry and connection clearance in the outline drawing.

Review dimensions ↑
02 / SELECT

Match the operating point.

Specify the supply voltage, speed, torque and duty cycle. Use the complete part code when selecting a configuration.

Review original data ↗
03 / VALIDATE

Evaluate in your assembly.

Check start-up behavior, load, clearances and operating temperature in the intended mechanism.

Discuss your application ↗

ENGINEERING ENQUIRY

Discuss this drive for your design.

Send your operating requirements and expected quantity. Reference GB15-154-DZ23008-1.

Contact NFP Motor ↗
Technical source FORWA / KH catalogue · Page 24 · GB15-154-DZ23008-1 Download source PDF ↓

Product image: AI-generated illustrative render based on the assembly drawing. Exact dimensions and variant details follow the technical drawing and specification tables.